Программирование брелков

[Norayr]

Люди, кто знает как запрогроммировать брелок на штатную сигнализацию

[Norayr]

montero sport

[SNOOPER]

PROGRAMMING
NOTE: Transmitter programming should be performed only after verifying that door lock operates normally using key.


NOTE: Ensure ignition is off when connecting or disconnecting scan tool.


ANSWERBACK FUNCTION CUSTOMIZATION
Activating/Deactivating Hazard Answerback Function
Ensure key is removed from ignition. While pressing UNLOCK switch for 4-10 seconds, push LOCK button on transmitter. Go to next step.
To activate or deactivate hazard answerback function customization feature when doors are unlocked, go to next step. To activate or deactivate hazard answerback function customization feature when doors are locked, release LOCK button then UNLOCK button on transmitter. ETACS-ECU will sound indicating that it is ready to be switched. Push LOCK button on transmitter again to activate or deactivate hazard answerback function. If ETACS-ECU sounds once when LOCK button is pushed, hazard answerback function is enabled. If ETACS-ECU sounds 2 times when LOCK button is pushed, hazard answerback function is disabled.
To activate or deactivate hazard answerback function customization feature when doors are unlocked, release UNLOCK button then LOCK button on transmitter. ETACS-ECU will sound indicating that it is ready to be switched. Push UNLOCK button on transmitter again to activate or deactivate hazard answerback function. If ETACS-ECU sounds once when UNLOCK button is pushed, hazard answerback function is enabled. If ETACS-ECU sounds 2 times when UNLOCK button is pushed, hazard answerback function is disabled.
To exit hazard answerback function customization feature, turn ignition switch to position other than LOCK or open driver's door. If system remains inactive for at least 3 minutes after ETACS-ECU has entered customize mode, hazard answerback function customization feature will cancel automatically.
Activating/Deactivating Horn Answerback Function
Ensure key is removed from ignition. While pressing LOCK switch for 4-10 seconds, push UNLOCK button on transmitter. Go to next step.
To switch between activating or deactivating horn answerback function customization feature, release LOCK and UNLOCK buttons simultaneously. If ETACS-ECU sounds once when LOCK and UNLOCK buttons are released, horn answerback function is enabled. If ETACS-ECU sounds 2 times when LOCK and UNLOCK buttons are released, horn answerback function is disabled.
RKE TRANSMITTER
NOTE: Transmitter programming should be performed only after verifying that door lock operates normally using key. All transmitter codes must be registered when Electronic Time Alarm Control System (ETACS) ECU is replaced, a new transmitter is to be added, or a problem with a registration code is expected. Scan tool must be used to register transmitters.


Two different transmitters may be registered per vehicle. When a new code is registered for a transmitter, all additional transmitters used must be reprogrammed to new code.

Ensure ignition switch is in LOCK position. Connect scan tool to Data Link Connector (DLC). DLC is located under left side of dash, next to center console. Scan tool will ground DLC connector terminal No. 1 to activate secret code registration mode. Within 10 seconds after connecting scan tool turn ignition switch to ON position for one second and to OFF position for one second 3 times.
Door should lock and unlock indicating system has switched to registration mode. Press any button on RKE transmitter one time and then 2 more times within 10 seconds. Doors will lock and unlock indicating that registration is complete. If registering a second transmitter, repeat procedure used to register first transmitter within one minute of registering first transmitter.
System will terminate registration mode when 2 transmitters have been registered, one minute after system has switched to registration mode and no action is taken, scan tool is disconnected, or ignition switch is turned to ON position. After registration is complete, remove ignition key and close all doors. Ensure keyless entry system operates properly.

[Norayr]

Просто класс, а перевести не могу. переводчики пишут какую то хрень.

может у кого на русском инфа есть.